BYCPC - N4787A HI IR 686 TAN
- MSDS: BYCPC
- Manufacturer: NILES CHEMICAL PAINT CO
- Product Name: N4787A HI IR 686 TAN
- National Stock Number: 8010-01-260-0909
Product Identification
Product ID:N4787A HI IR 686 TAN
MSDS Date:07/25/1995
FSC:8010
NIIN:01-260-0909
Kit Part:Y
MSDS Number: BYCPC
Responsible Party
NILES, MI 49120
US
Emergency Phone: 219-236-5856
Info Phone: 616-683-3377
Preparer: MIKE LICHATOWICH
Cage: 02388
Contractor
Telephone: 616-683-3377/219-236-5856
Cage: 02388
Ingredients
NO INGREDIENT FOR THIS FORMULATION_INGREDIENT
Hazards
Routes of Entry: Inhalation:YES Skin:NO Ingestion:YES
Reports of Carcinogenicity:NTP:NO IARC:NO OSHA:NO
Health Hazards Acute and Chronic:ACUTE: EYES: SEVERE IRRITATION,
LACRIMATION, REDNESS, BLURRED VISION. SKIN: REDNESS, IRRITATION,
DEFATTING LEADING TO DERMATITIS. BREATHING: NASAL & RESPIRATORY
IRRITATION, CNS DEPRESSION, ASPHYXIATIO N. INGESTION:
GASTROINTESTINAL IRRITATION. CHRONIC: HISTOLOGIC FIBROSIS OF LUNGS,
NARCOSIS, COMA.
Explanation of Carcinogenicity:NOT LISTED BY NTP, IARC OR OSHA.
Effects of Overexposure:BREATHING: DIZZINESS, DROWSINESS, WEAKNESS,
FATIGUE, CONFUSION, NAUSEA, HEADACHE, VERTIGO, POSSIBLE
UNCONSCIOUSNESS. INGESTION: ABDOMINAL PAIN, NAUSEA, VOMITING,
DIARRHEA.
Medical Cond Aggravated by Exposure:NK. TARGET ORGANS: RESPIRATORY
SYSTEM, CNS, LUNGS, EYES, SKIN.
First Aid
First Aid:INHAL: GET FRESH AIR. IF BREATHING STOPPED, START ARTIF RESP.
GET MED AID. SKIN: IMMEDIATELY FLUSH W/WATER. IF MAT'L PENETRATES
CLOTHING, REMOVE CONTAM CLOTHING, FLUSH SKIN W/WATER. GET MED AID.
EYES: IMMED FLUSH W/LRG AMT WATER 15 MIN, LIFTING EYELIDS. GET MED
AID IMMED. INGESTION: DRINK 1-2 GLASSES WATER. DON'T INDUCE
VOMITING. CONSULT PHYSICIAN/POISON CONTROL CENTER IMMED. TREAT
SYMPTOMATICALLY
Fire Fighting
Flash Point Method:TCC
Flash Point:20.0F,-6.7C
Lower Limits:1.0
Upper Limits:10.0
Extinguishing Media:DRY CHEMICAL, FOAM, CO2.
Fire Fighting Procedures:WEAR POS PRESS SCBA W/FULL FACEPIECE & FULL
PROTECTIVE CLOTHING. WATER MAY BE USED TO COOL CLOSED CONTAINERS TO
PREVENT PRESS BLD UP & AUTOIGNIT/EXPLOS.
Unusual Fire/Explosion Hazard:VAPOR HEAVIER THAN AIR, TRAVEL TO IGNIT
SOURCE. ISOLATE FROM IGNIT SOURCE. CLSD CNTNR EXPLODE W/HEAT.
APPLICATION TO HOT SURFACES REQUIRES SPECIAL PRECAUTIONS.*
Accidental Release
Spill Release Procedures:NO IGNIT SOURCES. MINIMIZE BREATHING VAPORS.
AVOID SKIN CONTACT. SM: ABSORB W/INERT MAT'L (CLAY, SOIL, COMMERC
ABSORB) SHOVEL RECLAIMED LIQ & ABSORB INTO RECOVERY/SALVAGE DRUMS.
LG: DIKE (NO FURTHER M OVEMT) & RECLAIM INTO SALVAGE DRUMS/TANK
TRUCK.
Handling
Handling and Storage Precautions:AVOID STORAGE IN HIGH TEMP AREAS OR
NEAR FIRE OR OPEN FLAME. KEEP CONTAINERS TIGHTLY CLOSED WHEN NOT IN
USE. AVOID ROUGH HANDLING.
Other Precautions:CONTAINERS OF THIS MATERIAL MAY BE HAZARDOUS WHEN
EMPTY. DO NOT WELD OR FLAME CUT ON EMPTY DRUMS. DO NOT WEAR CONTACT
LENSES WHEN WORKING W/THIS MATERIAL.
Exposure Controls
Respiratory Protection:WEAR APPROP (TC-23C-75) FITTED HALF-MASK FOR
FULL FACEPIECE RESPIRATOR (NIOSH/MSHA) DURING/AFTER APPLICATION
UNLESS AIR MONITERING DEMONSTRATES VAPOR/MIST LEVELS BELOW TLV.
FOLLOW RESPIRATOR MFR DIREC TIONS FOR USE.
Ventilation:PROVIDE SUFFICIENT VENTILATION (VOLUME/PATTERN) TO KEEP AIR
CONC BELOW TLV PEL. REMOVE DECOMP PROD. VENT VAPOR EMITTED.
Protective Gloves:CHEM RESISTANT, NITRILE OR VITON
Eye Protection:CHEM GOGGLES/SAFETY GLASSES/FACE SHIELDS
Work Hygienic Practices:WASH ANY CONTAM CLOTHING OR CLOTH THAT BECOMES
WET BEFORE REUSE. WASH HANDS BEFORE EATING, SMOKING OR USING
RESTROOM.
Supplemental Safety and Health
NK
Chemical Properties
Boiling Pt:B.P. Text:175 TO 302F
Vapor Density:>AIR
Spec Gravity:1.393
pH:NA
Viscosity:70-85 KU
Evaporation Rate & Reference:SLOWER THAN ETHER
Solubility in Water:SLIGHT
Appearance and Odor:LIQUID, SOLVENT ODOR
Percent Volatiles by Volume:59.73
Corrosion Rate:MINIMAL
Stability
Stability Indicator/Materials to Avoid:YES
STRONG OXIDIZERS, NITRATES, ALKALIES, ACIDS.
Stability Condition to Avoid:NK *OVEREXPOS TO DECOMP PROD MAY CAUSE
HEALTH HAZARD. SYMPTOMS MAY NOT BE IMMED APPARENT. GET MED AID.
Hazardous Decomposition Products:CAN PRODUCE CARBON MONOXIDE &/OR
CARBON DIOXIDE.
Conditions to Avoid Polymerization:HIGH TEMPERATURES
Disposal
Waste Disposal Methods:DISPOSE IN ACCORDANCE W/FEDERAL, STATE, LOCAL
REGULATIONS. EPA HAZ WASTE CODE: D001 (IGNITABLE).
Disclaimer (provided with this information by the compiling agencies):
This information is formulated for use by elements of the Department
of Defense. The United States of America in no manner whatsoever,
expressly or implied, warrants this information to be accurate and
disclaims all liability for its use. Any person utilizing this
document should seek competent professional advice to verify and
assume responsibility for the suitability of this information to their
particular situation.